Foundation waterproofing "TechnoNIKOL" is widespread today due to a wide range, excellent technical characteristics and high quality, which allows you to choose the material for even the most complex structures. Protecting the surface from moisture with the help of TechnoNIKOL brand materials can be done in several ways, among them: coating, impregnating and pasting.
Laying waterproofing
If you prefer to use gluing waterproofing, then you can choose one of the TechnoNIKOL brand materials. For example, "Technoelast EPP" is a surfacing material in the form of rolls for waterproofing. It is made on the basis of fiberglass or polyester, and bitumen-polymer layers are located on both sides. The outer side has a reinforcement in the form of fine-grained dressing, while the inner surface consists of a polymer film. The material is biologically stable, as well as the ability to undergo hydrostatic loads that reach an indicator of0.2 MPa. This waterproofing of the TechnoNIKOL foundation is intended for structures located on soil, to the surface of which groundwater is close. Technoelast EPP is used in those areas where seasonal ground movements are noted. Installation is carried out horizontally or vertically using fusing technology.
Alternative options for gluing waterproofing brand "TechnoNIKOL"
"Technoelast ALFA" is a deposited roll material, which is made on the basis of double-sided polyester raw materials. It is reinforced with foil, and the coating is represented by bitumen, supplemented with a polymer plasticizer. A polymer film acts as a protective coating. This waterproofing is used for foundations that can emit radioactive radon gas during operation. Very convenient to use varieties of "Technoelast Barrier" and "Barrier Light", which have self-adhesive layers consisting of a polymer film. You can use the material for both external and internal work, which is convenient for waterproofing basements. The last variety listed has a layer of non-woven material, which is located on the outside of the film. This greatly facilitates further finishing work. The waterproofing of the TechnoNIKOL foundation is represented by another type of roll material - Technoelast MOST, which is used to protect horizontal bases that are resistant to bursting and increaseddurability.
Features of using TechnoNIKOL gluing waterproofing
The TechnoNIKOL foundation adhesive waterproofing is used in compliance with a certain technology. At the first stage, the foundation is prepared, its base is leveled, the protrusions are removed, and the potholes are rubbed with cement mortar. The surface is tapped, degreased, gets rid of traces of rust and paint. The protruding reinforcement should be disposed of, and before laying the roll material, the surface should be coated with a primer and dried. Next, a layer of coating waterproofing is applied, which is maintained until it is completely cured. After the foundation is ready for fixing roll materials. If you have a material with a self-adhesive layer in front of you, then it should be pressed tightly and rolled with a hard wide roller.
On a horizontal plane, laying is carried out in such a way as to obtain the minimum number of joints. Vertical waterproofing is made of separate strips, which must first be cut along the height of the foundation. The width of the overlap should be approximately 15 millimeters. Each next layer is laid with the central part of the strip on the seam of the previous one. In this case, the staggered order should be observed.
Coated insulation
The manufacturer "TechnoNIKOL" produces compositions that can be used for sprayed and coating waterproofing. The latter variety is produced usingpolymer, bituminous and combined mastics of cold and hot application. Their difference is the temperature of the mixture. Coating waterproofing of the TechnoNIKOL foundation in the form of hot mastics is more difficult to use, but it penetrates deeper, fills cracks and capillaries. Cold mastics are two-component and one-component, the first of them require mixing with an activator before starting work. Primers are used to improve the quality, they look like primers for bitumen-rubber or concrete mortars.
Common varieties of coating insulation brand "TechnoNIKOL"
If waterproofing the foundation with TechnoNIKOL mastic is more preferable for you, then you can purchase composition No. 21, which is represented by a mixture with increased strength. Water resistance can reach 0.1 MPa, which was achieved due to the presence of a rubber modifying additive. The mixture is applied cold, and at sub-zero temperatures, the composition will need to be heated. To achieve a positive result, at least two layers must be applied. On sale you can find one-component bitumen mastic No. 24 MGNT, in the manufacturing process of which additives are used in the form of a mineral reinforcing filler. Mastic is intended for cold use, application is carried out with a roller or brush in several layers. This bituminous waterproofing of the TechnoNIKOL foundation is capable of undergoing a hydrostatic load, whichreaches an indicator of 0, 001 MPa. An effective mixture for waterproofing structures from capillary moisture. If you have to work with a porous surface, then it should first be coated with a primer. The solvent for the mastic is white spirit. No. 25 bituminous varnish is used to treat concrete surfaces, it is intended for the top of the base and can be used as a primer for painting.
Description of water-based mastic and hot use mastic
If you will be waterproofing the foundation, TechnoNIKOL materials are perfect for this. You can choose, for example, TechnoNIKOL mastic No. 31 or No. 33. Both varieties are water-based and are water-based mixtures for spraying. In the manufacturing process, dispersed petroleum products and emulsified latex are used. For ease of application, you can use a mechanized method, while the water permeability will reach 0.1 MPa per day. For hot use, MBK-G mastic can be purchased, which is supplied in briquettes and requires heating up to 180 degrees. The application is carried out with a spatula, and the surface is pre-treated with a primer. Pros include fast curing and low cost.
Description of primer 04
This bituminous mastic for waterproofing the TechnoNIKOL foundation canused as a primer on dusty and porous surfaces. The emulsion dries quickly, dissolves with water and can be used as a base for polymeric and mounted waterproofing rolls.
Cut-off waterproofing "TechnoNIKOL 200"
Foundation waterproofing "TechnoNIKOL 200" is a material that is made on the basis of polyester. It is impregnated with bitumen-polymer binder, and Spunbond is covered on both sides. It is used to protect partitions, walls and Mauerlat from capillary rise of moisture. The material is laid on bituminous mastic or mortar and is supplied in conveniently cut rolls, which have three sizes. The material is reliable and durable, within 6 months it will endure exposure to ultraviolet rays. Its service life reaches 50 years, and the base is durable and is not a suitable environment for the occurrence of putrefactive processes.
Characteristics of the cut-off waterproofing brand "TechnoNIKOL 200"
Rolled waterproofing "TechnoNIKOL" for the foundation has a mass within one kilogram per square meter. Within 24 hours, water absorption does not exceed 1%, heat resistance is 100 degrees. It is important to take into account the relative elongation, which can exceed 30%. When stretched, the breaking force is 344 N.
